Pool is a great source of recreational activity at your home. It does not only provide you with the facility of swimming in a safe clean environment, but also enhances the decoration of your home. Your pool is the attraction of your yard, so you will want to keep it dazzling clean all season long. So it must be well maintained and cleaned.
To maintain the hygiene of your, swimming pool you need to continuously take care of it by vacuuming, brushing the water lines, and adding algaecide for salt pools. It is not a neglectable duty, as debris on the bottom of a pool can lead to algae growth, and you would never find it pleasurable to swim in slimy, green water. Now let’s us show you how this is done below…
How to vacuum above-ground pool
After finding the best cleaner, your job is to how to carry out procedures. To undertake the procedures effectively vacuum an above ground pool includes:
Things you need
Make sure you have arranged the things you are going to need for this process. The manual of vacuum system Consists of:
- Pool leaf rake or skimmer
- A head with brushes and roller on it
- Vacuum ribbed plastic hose
- A long metal o fiberglass pole
- Vacuum head
- Extension pole
- Skimmer disk (optional)
- An adapter
Step-by-step process to vacuum above-ground pool
- Remove leaves, bugs, and other surface debris from the lake, using a leaf rake or skimmer. If required, inspect and clean the skimmer basket. Make sure the pump is turned on and that water is flowing through the filter.
- The hose will fill with water, expelling any trapped air. Place the vacuum plate into the skimmer while keeping the hose submerged and the leaf basket in place. Quickly attach a hose to the elbow fitting. It’s ready now ready to vacuum.
- Attach the vacuum hose’s swivel end to the vacuum head. Connect the extension pole to the head. Lower the assembly into the pool and stretch the pole until the vacuum head meets the water’s surface. Lean the pole against the pool’s edge, within easy reach of the water return outlet, and lock it into position.
- Fill the vacuum hose with water by keeping the free end in front of the water return outlet. As air is released from the hose, keep one hand on the pole to keep the head from floating to the surface. Continue priming the hose until it is filled with water and no more bubbles are rising from the vacuum head.
- Pull the hose away from the water return outlet and attach the skimmer disc while keeping the hose end submerged. To start the vacuum, insert the skimmer disc into the skimmer on top of the suction port. Some vacuums, on the other hand, involve directly plugging the hose end into the suction port. To avoid getting too much air back into the hose, pull the hose end out of the water as soon as possible to fit it or the skimmer disc into the suction port.
- Get into a spot where you can see the pool’s bottom. Slowly move the vacuum head back and forth across the pool’s floor, slightly overlapping the previous direction with each new run. To avoid losing the prime, Keep the head underwater at all times. Continue the process until the bottom is completely clean of debris.
Points to remember during vacuuming
- Brush the pool’s sides the night before vacuuming to loosen dirt, then vacuum the next morning before anyone uses it.
- Adjust the water returns so that the water mass travels in a circular pattern all of the time.
- Never put any part of your body directly in contact with a pool’s suction port; this helps concentrate debris on the middle of the pool floor, where it’s easier to vacuum. There’s a chance you’ll get injured badly.
Air is the enemy of a pool filter and vacuum system. Before connecting the vacuum hose, make sure that line is not filled with air. There are two ways to avoid air in your vacuum.
- Slowly lower the vacuum head into the pool when attached to the hose and pole. Continue to slowly feed the hose into the tub. This causes the hose to fill up as it reaches the tub. Lower the filter adapter-connected cuff to the water’s edge. Until submerging the hose’s end, check to see if the hose has filled with water. Repeat the process if no water is visible. Keep the loose cuff below the water level once the hose is full of water.
- Start by slowly submerging the vacuum head into the pool to extract air from a pool hose through the filter system. Then, with the loose end in your lap, place the rest of the hose into the tub. Find the return from the filter. Place the hose’s loose end against the return to allow water to flow through it. Since the vacuum head can bounce as pressure expels air from the hose, hold the pole tightly. The hose is ready when the air bubbles stop. Maintain the loose cuff’s position underneath the surface.
Can I vacuum the pool without a skimmer?
If you don’t have a skimmer, you can manually clean your pool with a few inexpensive tools. You may use a vacuum system to suck debris out of the pool by connecting it to a skimmer inlet. Due to the lack of a skimmer in your tub, the inlet would be free to fit the vacuum hose.
Automatic or manual pool cleaner?
Even if you have an automated pool cleaner, you will occasionally need to use your manual pool vacuum. A manual pool vacuum is needed if you have a pool. Algae blooms are one of the many problems that your automated pool cleaner can’t solve. You’ll need to shock your tub, use algaecide, and then manually clean it to get rid of the algae.
Above-ground, swimming pools need less maintenance than in-ground pools. Vacuuming your pool not only eliminates contaminants from the water but also keeps the pool as fresh as possible. Vacuuming is a regular activity, so you need to find the best pool vacuum cleaner. It will make your job easy and effective and will serve you for the longest time.